Limited Time Offer!
Selling Price -$26,532.00
12' cutting width, 1 1/2" cutting capacity, 40-100hp recommended. pto driven, 5 year gearbox warranty
FEATURES
Note: Some feature photos may be represented by a similar model and not the specific model shown on this page.
GEARBOX WARRANTY
5 Year Limited Gearbox Warranty demonstrates our confidence in the gearbox's quality and lasting performance.
1-1/2" CUTTING CAPACITY
These cutters offers 1-1/2" cutting capacity. See Operator's Manual for more information.
OPTIONAL LP PERFORMANCE HITCH
Clevis swivels two ways: Cutter can swivel clockwise and counterclockwise about tractor drawbar up to 12° in either direction.
ADJUSTABLE JACK ANGLE
Helps keep park jack vertical when in use.
LED SIGNAL LIGHTS
LED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.
BEVELED SKID SHOES
Wing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.
10 GAUGE STUMP JUMPER
Round stump jumper allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.
CENTER SPRING
Center spring on the cylinder cushions load on drawbar.
DUAL LEVELING RODS
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain.
NARROW TONGUE DESIGN
Narrow tongue design handles tight turns - great size for country estates.
Pricing does not include - freight, pdi, set up, delivery or install.
FEATURES
Note: Some feature photos may be represented by a similar model and not the specific model shown on this page.
GEARBOX WARRANTY
5 Year Limited Gearbox Warranty demonstrates our confidence in the gearbox's quality and lasting performance.
1-1/2" CUTTING CAPACITY
These cutters offers 1-1/2" cutting capacity. See Operator's Manual for more information.
OPTIONAL LP PERFORMANCE HITCH
Clevis swivels two ways: Cutter can swivel clockwise and counterclockwise about tractor drawbar up to 12° in either direction.
ADJUSTABLE JACK ANGLE
Helps keep park jack vertical when in use.
LED SIGNAL LIGHTS
LED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.
BEVELED SKID SHOES
Wing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.
10 GAUGE STUMP JUMPER
Round stump jumper allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.
CENTER SPRING
Center spring on the cylinder cushions load on drawbar.
DUAL LEVELING RODS
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain.
NARROW TONGUE DESIGN
Narrow tongue design handles tight turns - great size for country estates.
Pricing does not include - freight, pdi, set up, delivery or install.
- 2024
- Land Pride
- RC2512 Series
- Base
- Rotary Cutters
- Tractor horsepower: 40-100 hp (30-75 kW)
- Gearbox capacity - Splitter: gear lube 80-90W EP / Center & wings: gear lube 80-90W EP
- Gearbox horsepower Splitter: 160 hp (119 kW) / Center & wings: 100 hp (75 kW) | 6 Spline
- Input: Category 4 with constant velocity u-joint | Intermediate & wing: Category 3 with slip-clutch
- 20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires or 21" (53.3 cm) laminated wheels | Number of: 4 - Wheels: 2 on transport axle and one on each wing axle
- Blade tip At 540 rpm - Center Blades = 16,500 FPM (83.8 mps) / Wing Blades = 16,000 FPM (81.3 mps)
- LP Performance hitch and swivel hitch
- Signal: LED / 7 Pin connector: SAE J560 pin configuration
- Gearbox shafts Input shaft: 1 3/8" (3.5 cm) 6 Spline / Output shaft: 1 1/2" (3.8 cm) | Cutting capacity: 1 1/2" (3.8 cm) | Lift hydraulics: 2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings and stroke control spacers | Wing folding hydraulics: 2" bore x 8" stroke hydraulic cylinders, hoses, and fittings | Wing flex while operating: Max. 20° down, can float up as needed as long as the wheel(s) are still on the ground. | Blades - 6 (2 per deck): 1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift | Blade overlap: 6" (15.2 cm) | Stump jumper / blade holder: 10 Gauge (3.4 mm) round dish shaped pan, reinforced with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar
- 12'-0" (3.66 m)
- cutter: 12'-7" (3.84 m)
- Minimum: 7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground.
- 13'-3" (4.04 m)
- 11" (27.9 cm)
- Cutting: 1 1/2" to 12" (3.8 cm to 30.5 cm)
- Gearbox capacity - Splitter: 4.5 pints (2.13 L) / Center & wings: 4 pints (1.89 L)
- Wing transport protection: Wing transport locks | Skid shoes - Wing deck: 1 replaceable per wing / Center deck: 2 replaceable shoes | Blade rotation Left wing: Counterclockwise / Center deck: Counterclockwise / Right wing: Clockwise | Blade bolt: Keyed with hardened flat washer and locknut | Front & rear guards: Single chain | Transport axle: Spring-cushioned lift cylinder
- Hitch: 793 lbs (359.7 kg) | Machine: 2,540 lbs (1152.1 kg)
- 10 Gauge (3.4 mm) deck
- Side skirt: 3/16" (5 mm) Plate
- Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.
- $26,532.00
- Cobden, Ontario
- New
- 2024
- Land Pride
- RC2512 Series
- Orange
- Available
- Cutting: 1 1/2" to 12" (3.8 cm to 30.5 cm)